1. Bmw Dme Programming

BMW E46: change VIN in DME with BMW ICOM WinKFP software. Posted on April 23, 2015 by sales. Here is the detail instruction on updating/reprogramming the DME module and change the VIN stored in the DME dump with BMW WinKFP software. Tool needed: BMW ICOM A2+B+C WIFI OBDⅡdiagnostic system. The important note- if you flash the DME with WinKFP it will change the VIN to the one you type. If not, Tool32 can do it. (With tool 32 you must enter 18 ) However depending on DME, you may not be able to use a second hand DME to another car because of ISN issues. WinKFP Guide: how to change VIN number on BMW. May 24, 2017 sales BMW. DIY flash Alpina B3 with BMW ICOM Winkfp Here is the DIY guide just provides the instructions on how to flash BMW Alpina B3 with the Winkfp software. Note: I do not hold any responsibility if you damage your car.

Here is an example of coding BMW E46 M3 (with SMG2 transmission) Euro SMG mode also called 'CSL Coding' with BMW ICOM engineering and developing WinKFP coding software.

Bmw Dme Programming

Equipment: BMW ICOM ISTA/D ISTA/P with WinKFP 5.1.6 or newer version software HDD and 46 data files BMW ICOM A2+B+C diagnostic and programming tool Stable power supply 13-14V at 10A (very important)

Instruction:

Well install BMW ICOM ISTA/D ISTA/P software HDD Select and run WinKFP software on the desktop Click Import/Export ->Import ->Assembly Line Data

Browse to the unzipped SP-Daten-E46 folder and select the “data” folder. Press “OK” and wait a few minutes to load the data.

Click “Configuration” and do some settings, language, file destination etc, make sure the program configuration setting is the same as picture below:

Save settings and exit WinKFP software.

2) Flash/Program CSL module

Browse the unzipped SP-Daten-E46 folder to: Copy the contents of the ecu folder to C:/EDIABAS/Ecu Copy the contents of the sgdat folder to C:/EC-APPS/NFS/SGDAT

Run WinKFP software again Turn ignition ON

NOTE: Keep the vehicle voltage at 13-14V. If the voltage is below 12.5V or above 14.5V, the flashing procedure may fail and results in brick the module.

Run WinKFP and select “Comfort Mode” Click “Enter ZUSB”, select ECU type: GDSMG2 and choose ZB-number: 7843255. Click OK.

Click “Enter VIN” and manually enter 17-digit VIN correctly Press “Done” You will be displayed the vehicle information and the boost section update activated message.

Click “F3: Program”. WinKFP will give you a message about having X number of flashes available. Press Ok to accept the notice

The module flashing is processing. Accept the windows prompt if the flashing stops at 100%. And it will go faster and complete programming.

Turn ignition OFF Turn ignition ON after 5 minutes. Clear the stored DTCs in control module with BMW INPA software.

Turn the ignition off and wait a few minutes again if the transmission error light is still on.

Max rune pages lol. What's the max amount of Rune Pages we can have now? What's the max amount of Rune Pages we can have now?.Culture. Here you’ll find all sorts of discussions related to playing League of Legends. From discussions about your personal strategies, to speculation about the next champion or patch, if it’s about playing the game, it goes. I bought 21st rune page. How many rune pages can i buy?

Start the engine and enjoy the improved shifts. You may need to run the SMG adaptation procedures.

The whole procedure takes about 15 to 30 minutes. Do not exit the software program or disconnect the BMW ICOM diagnostic tool with vehicle, otherwise, the SMG module will be bricked.